Our activities in the Energy Industry
Presentation of our Energy Industry projects
On this page we have presented a selection of the projects we have done in the Energy Industry. Our engineers are flying all over the world. If you click on a link listed below, you will be taken to the project page where all details and pictures of the project can be found.
The conversion operations consists of:
- Disassembling the complete gearbox from the platform.
- Transporting to our workshop.
- Performing of the repair constructions.
Singapore
August 2013
The conversion operations consists of:
- Disassembling the complete gearbox from the platform.
- Transporting to our workshop.
- Performing of the repair constructions.
Singapore
August 2013
The conversion operations consists of:
- Disassembling the complete gearbox from the platform.
- Transporting to our workshop.
- Performing of the repair constructions.
Singapore
July 2013
The conversion operations consists of:
- Removing of the protection covers.
- Disassembling of the oil lines.
- Disassembling of the old oil pump.
Singapore
July 2013
The conversion operations consists of:
- Verification of mechanical run-out values.
- Recording and analyzing of relative shaft vibrations.
- Installatioin of trim balance weights on the steam turbine coupling hub.
Poland
May 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
The Netherlands
April 2013
The conversion operations consists of:
- Disassembling the complete gearbox from the platform.
- Transporting to our workshop.
- Performing of the repair constructions.
Singapore
March 2013
Oman
February 2013
Turkey
December 2012
Dominican Republic
November 2012
The conversion operations consists of:
- Performing a visual inspection of the gearbox.
- Performing of the repair constructions.
- Deploying of the inspection report.
Belgium
October 2012
Switzerland
September 2012
The Netherlands
July 2012
The Netherlands
June 2012
The Netherlands
May 2012
Scotland
May 2012
The Netherlands
April 2012
The Netherlands
February 2012
The Netherlands
January 2012
Norway
December 2011
The Netherlands
November 2011
The Netherlands
October 2011
The Netherlands
September 2011
Poland
June 2011
Poland
May 2011
- Transporting to our workshop.
- Performing of the repair constructions.
CFEM 27H6SP
Singapore
August 2013
- Transporting to our workshop.
- Performing of the repair constructions.
CFEM 27H6SP
Singapore
August 2013
- Transporting to our workshop.
- Performing of the repair constructions.
CFEM 27H6SP
Singapore
July 2013
- Disassembling of the oil lines.
- Disassembling of the old oil pump.
RENK HSUSL-1020
Singapore
July 2013
- Recording and analyzing of relative shaft vibrations.
- Installatioin of trim balance weights on the steam turbine coupling hub.
LUFKIN 2DYRPE8-IIIB-III
Poland
May 2013
- Deploying of the inspection report.
- Stop point.
DELROYD KE80-44T-18,5
The Netherlands
April 2013
- Transporting to our workshop.
- Performing of the repair constructions.
CFEM 27H6SP
Singapore
March 2013
First we perform an inspection on gearbox of Flender.
After that we repair the damage.
Re-assemble it again.
At the end, we also perform an alignment.
After that we repair the damage.
Re-assemble it again.
At the end, we also perform an alignment.
FLENDER TRL 65 CV
Oman
February 2013
Inspection and revision on gearbox SIEMENS 5311-962.
Disassembling and inspection onsite.
Inspection in order to check the clearance.
Disassembling and inspection onsite.
Inspection in order to check the clearance.
SIEMENS 5311-962
Turkey
December 2012
Inspection on gearbox Flender Graffenstaden AA 51 DA.
We found that the gears were damaged.
We immediately repaired them on site.
We found that the gears were damaged.
We immediately repaired them on site.
FLENDER GRAFFENSTADEN AA 51 DA
Dominican Republic
November 2012
- Performing of the repair constructions.
- Deploying of the inspection report.
FLENDER GRAFFENSTADEN TX61 / 1CV
Belgium
October 2012
Trouble shooting suspicous vibrations on a steam turbine.
ELLIOTT UNKNOWN
Switzerland
September 2012
Performing a visual inspection on gearbox Lohmann & Stolterfoht GPV 441 S1 PG.
We inspected the gears for any damage and made an inspection report.
We inspected the gears for any damage and made an inspection report.
LOHMANN & STOLTERFOHT GPV 441 S1 PG
The Netherlands
July 2012
- Exchange bearings onsite.
- Assembling and advise our client.
- Assembling and advise our client.
FLENDER SDNK 1650
The Netherlands
June 2012
Exchanging bearings, assembling and advise our client.
FLENDER SDNK 1650
The Netherlands
May 2012
For our client in Scotland we performed a visual inspection
on gearbox Rexroth GPV 306. Our engineers also
performed a vibration measurement on a wind turbine.
on gearbox Rexroth GPV 306. Our engineers also
performed a vibration measurement on a wind turbine.
REXROTH GPV 306
Scotland
May 2012
We performed an inspection and revision on gearbox Bauer DF8A417E/680K.
After inspection one gear set was rejected to reuse in the gearbox. We made a new gear set and continued revision according to our revision report.
After inspection one gear set was rejected to reuse in the gearbox. We made a new gear set and continued revision according to our revision report.
BAUER DF8A417E/680K
The Netherlands
April 2012
Broaching gearbox FLENDER SDNK 1650 onsite.
Assist and giving advise to our client about: - Assembling the bearings.
- Disassembling the gearbox.
Assist and giving advise to our client about: - Assembling the bearings.
- Disassembling the gearbox.
FLENDER SDNK 1650
The Netherlands
February 2012
Our client had problems with gearbox WINERGY PEAB 4395.
They called us for an inspection to find the cause of the problem.
We inspected the whole gearbox and performed adjustment where needed.
They called us for an inspection to find the cause of the problem.
We inspected the whole gearbox and performed adjustment where needed.
WINERGY PEAB 4395
The Netherlands
January 2012
On gearbox Hansen II-A33K-28-ANBR we performed an inspection.
We renewed all bearings, seals and performed a test run onsite.
We renewed all bearings, seals and performed a test run onsite.
HANSEN II-A33K-28-ANBR
Norway
December 2011
Inspection of gearbox Lohmann & Stolterfoht.
We inspected this gearbox for any tears or damages.
We inspected this gearbox for any tears or damages.
LOHMANN & STOLTERFOHT GPV 441 S1 PG
The Netherlands
November 2011
Performing a visual inspection with endoscope onsite.
Including inspection report for our client.
Including inspection report for our client.
VESTAS V52-850
The Netherlands
October 2011
Our client had a problem with gearbox Lohmann & Stolterfoht.
We inspected the gearbox and reported all our findings to our client.
We managed to repair the damage and assembled the gearbox.
We inspected the gearbox and reported all our findings to our client.
We managed to repair the damage and assembled the gearbox.
LOHMANN & STOLTERFOHT GPV 400 333113R
The Netherlands
September 2011
This gearbox of WINERGY PEAB 4435 had several damaged.
We performed an inspection and overhauled/replaced the gearbox.
We performed an inspection and overhauled/replaced the gearbox.
WINERGY PEAB 4435
Poland
June 2011
Inspection and overhaul of gearbox of brand Lohmann & Stolterfoht in Tymien, Poland.
LOHMANN & STOLTERFOHT GPV 441
Poland
May 2011