Global Activities
Our activities in Belgium
On this page you will find a selection of the projects we have done in Belgium. Since Belgium is only a few hours away from our headquarters in The Netherlands, we have done a lot of projects in this country. By clicking on one of the links below you can view the details of the project.
Belgium
January 2014
The conversion operations consists of:
- Performing of an alignment check before dismantling.
- Complete inspection of the gearbox.
- Deploying of the inspection report and measurement protocol.
Belgium
January 2014
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
Belgium
December 2013
The conversion operations consists of:
- Performing of a visual inspection of three Flender gearboxes on location.
- Performing of the repair constructions on location.
- Analyzing and deploying of the inspection report.
Belgium
December 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
Belgium
November 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Performing of the repair constructions.
- Renewing of all seals and bearings.
Belgium
October 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
Belgium
October 2013
Inside first gear set
- In way of the oil seal, rough-turn at seal location, add chrome to surface and fine-turn.
- The toothing is regrinded minimal.
Belgium
October 2013
The conversion operations consists of:
- Performing of a visual inspection of the Flender Graffenstaden gearbox.
- Performing of the repair constructions on location.
- Deploying of the inspection report.
Belgium
October 2013
The conversion operations consists of:
- A visual inspection of the gearbox on location.
- Deploying of the inspection report.
- Renewing of all seals, bearings and innerrings.
Belgium
October 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Performing of the repair constructions.
- Deploying of the inspection report.
Belgium
September 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
Belgium
September 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Deploying of the inspection report.
- Stop point.
Belgium
August 2013
The conversion operations for additional work:
- Performing of a visual inspection on location.
- Performing of the repair constructions.
- Analysing and deploying of a report.
Belgium
June 2013
The conversion operations for additional work:
- Performing of a visual inspection on location.
- Performing of the repair constructions.
- Analysing and deploying of a report.
Belgium
June 2013
The conversion operations consists of:
- Performing of a visual inspection of the gearbox.
- Performing of the repair constructions on location with the aid of a videoscope.
- Analysing and deploying of the inspection reports.
Belgium
June 2013
The conversion operations consists of:
- Disassembling, cleaning and inspection of the gearbox.
- Performing of the repair constructions.
- Deploying of the inspection report.
Belgium
May 2013
Belgium
March 2013
Belgium
March 2013
The conversion operations consists of:
- Performing of an inspection and a vibration measurement of the gearbox.
- Performing of the repair constructions.
- Deploying of the inspection report.
Belgium
February 2013
The conversion operations consists of:
- Performing of a visual inspection on two gearboxes.
- Performing of the repair constructions on location.
- The repair operations were deployed with the aid of an endoscope.
Belgium
February 2013
The conversion operations consists of:
- Performing of an alignment check on the dredge pump gearbox on location.
For the alignment check, a laser shaft alignment system was used.
With this system, the alignment of equipment can be measured accurately.
- Deploying of the inspection report.
Belgium
February 2013
The conversion operations consists of:
- Performing of a visual inspection of the gearbox with the aid of a videoscope on location.
- Analysing and deploying of the inspection report.
Belgium
January 2013
The conversion operations consists of:
- Performing of a visual inspection of the gearbox on location.
- Replacing of the input shaft bearings.
- Renewing of the couplingseals.
Belgium
January 2013
Belgium
January 2013
The follow instructions were produced at the gearbox:
Disassembling and cleaning of the gearbox.
Inspection of the parts consisting of the following instruction:.
FLENDER E2HL Size 10
Belgium
January 2014
- Complete inspection of the gearbox.
- Deploying of the inspection report and measurement protocol.
SIEMENS 5346-982
Belgium
January 2014
- Deploying of the inspection report.
- Stop point.
RENOLD RX02-814-B-118-ECE
Belgium
December 2013
- Performing of the repair constructions on location.
- Analyzing and deploying of the inspection report.
FLENDER H3-SH-14
Belgium
December 2013
- Deploying of the inspection report.
- Stop point.
RENOLD RX02-814-B-118-ECE
Belgium
November 2013
- Performing of the repair constructions.
- Renewing of all seals and bearings.
HANSEN RNF24-BNN-12,5
Belgium
October 2013
- Deploying of the inspection report.
- Stop point.
LEIPZIG GMBH 06-1434-03800-ESL
Belgium
October 2013
- The toothing is regrinded minimal.
HANSEN RNF24-BNN-12,5
Belgium
October 2013
- Performing of the repair constructions on location.
- Deploying of the inspection report.
FLENDER GRAFFENSTADEN 9721
Belgium
October 2013
- Deploying of the inspection report.
- Renewing of all seals, bearings and innerrings.
ABB HXR-450LH2
Belgium
October 2013
- Performing of the repair constructions.
- Deploying of the inspection report.
FRIEDRICH UE30S
Belgium
September 2013
- Deploying of the inspection report.
- Stop point.
HANSEN 811-AN
Belgium
September 2013
- Deploying of the inspection report.
- Stop point.
SEW RM-107-AM-00
Belgium
August 2013
- Performing of the repair constructions.
- Analysing and deploying of a report.
ABB FAN-DPSL.1800.S8
Belgium
June 2013
- Performing of the repair constructions.
- Analysing and deploying of a report.
ABB DMG-250
Belgium
June 2013
- Performing of the repair constructions on location with the aid of a videoscope.
- Analysing and deploying of the inspection reports.
ZPMC GRDC0300-98670
Belgium
June 2013
- Performing of the repair constructions.
- Deploying of the inspection report.
LIGHTNIN LS-75
Belgium
May 2013
Revisionconstruction and supply comprehensive:
- Disassembling and cleaning of the gearbox.
- Inspection of all parts of the gearbox:
- Disassembling and cleaning of the gearbox.
- Inspection of all parts of the gearbox:
- The conversion operations consists of: - Cleaning, scraping and coating of the outsidegearbox.
VALMET L500-2
Belgium
March 2013
We repaired all seals and bearings and the slow axis of gearbox Lohmann & Stolterfoht GJZ 1323.
The follow instructions were produced at the gearbox:
- Wearing part ring was renewed.
- The toothing of the pinion had sharp borders. These were manual purified.
- The slow axis is renewed.
The follow instructions were produced at the gearbox:
- Wearing part ring was renewed.
- The toothing of the pinion had sharp borders. These were manual purified.
- The slow axis is renewed.
LOHMANN & STOLTERFOHT GJZ-1323
Belgium
March 2013
- Performing of the repair constructions.
- Deploying of the inspection report.
TGW 107
Belgium
February 2013
- Performing of the repair constructions on location.
- The repair operations were deployed with the aid of an endoscope.
HANSEN RDH31A AND 50
Belgium
February 2013
For the alignment check, a laser shaft alignment system was used.
With this system, the alignment of equipment can be measured accurately.
- Deploying of the inspection report.
RENK NHIU
Belgium
February 2013
- Analysing and deploying of the inspection report.
JSW GP450T
Belgium
January 2013
- Replacing of the input shaft bearings.
- Renewing of the couplingseals.
LIGHTNIN 88S-75
Belgium
January 2013
Revisionconstruction and supply comprehensive:
- Disassembling and cleaning of the gearbox.
- Inspection of all parts of the gearbox:
Gearbox casing:
- A visual inspection of the gearbox casing for bursts.
- Disassembling and cleaning of the gearbox.
- Inspection of all parts of the gearbox:
VALMET UNKNOWN
Belgium
January 2013