GBS Gearbox Services international brand of Schaaf- en Boorwerk Rotterdam B.V.
Emergency Hotline

Global Activities

Our activities Europe

Update 22-08-2011
Here below are shown some of the countries in which we have worked:
Projects last 6 months
Projects more then 6 months
Projects in progress NOW
The list below shows a selection of the projects we have done, except projects in The Netherlands and Belgium, sorted by country:

Pagina:
Previous 1 2 3 4 5 ... 12 Next

  • The conversion operations consists of:
  • - Verification of mechanical run-out values.
    - Recording and analyzing of relative shaft vibrations.
    - Installatioin of trim balance weights on the steam turbine coupling hub.
    LUFKIN 2DYRPE8-IIIB-III
    The balance of a clutch of a Lufkin gearbox
    The balance of a clutch of a Lufkin gearbox
    Poland
    Poland
    May 2013
    This gearbox of WINERGY PEAB 4435 had several damaged.
    We performed an inspection and overhauled/replaced the gearbox.
    WINERGY PEAB 4435
    Inspection of gearbox WINERGY PEAB 4435 in Poland
    Inspection of gearbox WINERGY PEAB 4435 in Poland
    Poland
    Poland
    June 2011
    Inspection and overhaul of gearbox of brand Lohmann & Stolterfoht in Tymien, Poland.
    LOHMANN & STOLTERFOHT GPV 441
    Inspection of gearbox
    Inspection of gearbox
    Poland
    Poland
    May 2011
    Inspection and repair on JAHNEL-KESTERMANN CSBV 225 L gearbox
    JAHNEL KESTERMANN CSBV 225 L
    Inspection and repair on JAHNEL-KESTERMANN CSBV 225 L gearbox
    Inspection and repair on JAHNEL-KESTERMANN CSBV 225 L gearbox
    Portugal
    Portugal
    September 2017
    Inspection on the clearance.
    Assembling the gearbox.
    Checking if the gearbox is in a good condition.
    EISENBEISS ZSE-130
    Disassembling  and inspection gearbox Extruder Eisenbeiss ZSE-130 onsite
    Disassembling  and inspection gearbox Extruder Eisenbeiss ZSE-130 onsite
    Russia
    Russia
    December 2012
    For our client in Scotland we performed a visual inspection
    on gearbox Rexroth GPV 306. Our engineers also
    performed a vibration measurement on a wind turbine.
    REXROTH GPV 306
    Visual inspection and measurement on gearbox Rexroth GPV 306
    Visual inspection and measurement on gearbox Rexroth GPV 306
    Scotland
    Scotland
    May 2012
    Visual inspection with videoscope on gearbox FLENDER CS0280/710.
    FLENDER CS0280/710
    Inspection on gearbox FLENDER CS0280/710
    Inspection on gearbox FLENDER CS0280/710
    Serbia
    Serbia
    December 2010
       Revisionconstruction and supply comprehensive:
       - Disassembling and cleaning of the gearbox.
       - Inspection of all parts of the gearbox:

    • Gearbox casing:
    • - A visual inspection of the gearbox casing for bursts.
    FLENDER CS0-710
    Inspection and revision on Flender CS0-710
    Inspection and revision on Flender CS0-710
    Spain
    Spain
    August 2013
  • The conversion operations consists of:
  • - Disassembling and ispection of the gearbox on location.
    - Renewing of the axial-radial bearings of the input hollow shaft.
    - Refacing bearing surfaces of the hollow shaft.
    RENK TACKE HSU-800D
    Repair of white metall bearings of propulsion gearbox
    Repair of white metall bearings of propulsion gearbox
    Spain
    Spain
    February 2013
  • The conversion operations consists of:
  • - Performing a visual inspection.
    - Controlling the first intermediate shaft for micro pitting.
    - Performing of a videoscopic inspection.
    - Bringing back of the oil level under the maximum allowed.
    LOHMANN & STOLTERFOHT GUS450
    Inspection of 2 propulsion gearboxes for class Lloyds
    Inspection of 2 propulsion gearboxes for class Lloyds
    Spain
    Spain
    January 2013
    Troubleshooting on gearbox Flender bh 35 515 on site.
    Our client had problems with switching.
    The bearings were slightly damaged.
    We repaired them immediately.
    FLENDER bh35 515
    Trouble shooting on gearbox Flender in Spain
    Trouble shooting on gearbox Flender in Spain
    Spain
    Spain
    October 2012
    We performed on gearbox Lohmann & Stolterfoht:
    - Disassembled in order to check all bearings and gears.
    - Control measurements of all bearings and gears.
    - Removed the old and fitted the new drive gear wheel for the direct driven gear oil pump and cpp pump.
    - Investigated the reason for the beak down of the first driven pumps.
    - Fitted the new direct driven pumps.
    LOHMANN & STOLTERFOHT GUC 630/1342
    Performing an inspection on gearbox LOHMANN & STOLTERFOHT GUC 630/1342
    Performing an inspection on gearbox LOHMANN & STOLTERFOHT GUC 630/1342
    Spain
    Spain
    February 2012
    Visual inspection on the bearing of the starboard side thruster in Barcelona. Preparing first approach for modification.
    ROLLS ROYCE Thruster
    Inspection of thruster of brand Rolls Royce
    Inspection of thruster of brand Rolls Royce
    Spain
    Spain
    October 2010
    Inspection performed on the propulsion gearboxes of the NST xxxx. The Chief Engineer observed high temperatures near the input shaft bearing (motor side) of the starboard side gearbox.
    LOHMANN & STOLTERFOHT GWS 4245
    Inspection and repair of gearbox of brand CHONGQING
    Inspection and repair of gearbox of brand CHONGQING
    Spain
    Spain
    September 2010
  • Gearbox casing
  • - Outside box was in poor condition, we had to scrape, to polish,
       to degrease and to conserve in the excisting colour.
    - Inside box was in poor condition.
    HANSEN RNG24-S
    Inspection and revision on Hansen RNG24-S
    Inspection and revision on Hansen RNG24-S
    Sweden
    Sweden
    January 2014
    - Inspected gearbox Flender B4-HV-12D.
    - Disassembling and cleaning.
    - We made a complete inspection report for our client in Sweden.
    FLENDER B4-HV-12D
    Inspection and revision on gearbox Flender B4-HV-12D
    Inspection and revision on gearbox Flender B4-HV-12D
    Sweden
    Sweden
    October 2011
    - Inspected gearbox Flender B4-HV-12D in Sweden.
    - Broaching the cupboard housing.
    - Assembling the gearbox and send it to our client.
    FLENDER B4-HV-12D
    Inspection and revision on gearbox Flender B4-HV-12D
    Inspection and revision on gearbox Flender B4-HV-12D
    Sweden
    Sweden
    September 2011
    Trouble shooting suspicous vibrations on a steam turbine.
    ELLIOTT UNKNOWN
    Trouble shooting suspicous vibrations on a steam turbine
    Trouble shooting suspicous vibrations on a steam turbine
    Switzerland
    Switzerland
    September 2012
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Controlling of the serration for bursts with the aid of magnafluxing.
        - Controlling of the shafts for bursts.
    JAHNEL KESTERMANN M-1306-1
    Inspection and revision on gearbox Jahnel Kestermann M-1306-1
    Inspection and revision on gearbox Jahnel Kestermann M-1306-1
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Deploying of the inspection report.
        - Stop point.
    SIEMENS 355
    Inspection and revision on gearbox Siemens 355
    Inspection and revision on gearbox Siemens 355
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Deploying of the inspection report.
        - Stop point.
    SIEMENS 355
    Inspection and revision on gearbox Siemens 355
    Inspection and revision on gearbox Siemens 355
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Performing of a visual inspection of the gearbox.
        - Deploying of the inspection report.
        - Stop point.
    ASUG GL-100
    Inspection and revision on gearbox Asug GL-100
    Inspection and revision on gearbox Asug GL-100
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Deploying of the inspection report.
        - Stop point.
        - Performing of the repair constructions.
    FLENDER CG 26-100
    Inspection and revision on gearbox Flender GC-26-100
    Inspection and revision on gearbox Flender GC-26-100
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Deploying of the inspection report.
        - Replacing of the complete gearbox.
        - Stop point.
    FLENDER P3NB-9
    Inspection and revision on gearbox Flender P3NB-9
    Inspection and revision on gearbox Flender P3NB-9
    The Netherlands
    The Netherlands
    May 2014
  • The conversion operations consists of:
  •     - Disassembling, cleaning and inspection of the gearbox.
        - Deploying of the inspection report.
        - Stop point.
        - Performing of the repair constructions.
    WGW DKBH 1500/So
    Inspection and revision on gearbox WGW DKBH 1500/So
    Inspection and revision on gearbox WGW DKBH 1500/So
    The Netherlands
    The Netherlands
    May 2014

    Pagina:
    Previous 1 2 3 4 5 ... 12 Next