Our activities in Chemical Industry

Disassembling, inspection and cleaning of gearbox Conrad-Stork LTS-165-T-11C10. In addition, we make the inspection report.

We disassembled, inspected and cleaned gearbox CONRAD STORK LTS-165-T-11C10.

Inspection on gearbox Hansen QVRF2-CUN-11,2.
Disassembling of the gearbox.
Renewed all of the bearings and sealings.
Assembling the gearbox.
Performing a test run.

On this gearbox of Plenty we performed:
Disassembling, cleaning and inspection.
Making a complete inspection report for our client.
Assembling the gearbox again.

Performing:
- Disassembling, cleaning and inspection on gearbox Flender ZF-128-IEC-160.
- Inspection with inspection report.

Performing:
- Disassembling, cleaning and inspection.
- Revision according to revision proposal.
- Renew all bearings and seals.
- Assembling and making a test run with a test run report.

Disassembling, cleaning and inspection on gearbox Flender K-200K.
We discussed the inspection with our client.
After inspected the gearbox we made a complete inspection report.

Performing a standard overhaul on gearbox SEW SSG-5:
- Disassembling and cleaning all of the parts.
- Inspection with inspection report.

- Inspected gearbox Flender B4-HV-12D.
- Disassembling and cleaning.
- We made a complete inspection report for our client in Sweden.

Performing:
- Disassembling, inspection and cleaning gearbox Conrad-Stork LTS-165-T-11C10.
- Making an inspection report.

- Disassembling
- Cleaning and inspecting
- Performing an inspection report.

Revision on two gearboxes of Rademakers, including
disassembling and assembling on location.
In our workshop we were able to renew the bearings and
sealings. We replaced the repaired gearbox onsite.

Performing an inspection and overhaul of gearbox.

Disassembling, cleaning and inspection on gearbox Jahnel Kestermann CSBV 225L.
Preparing inspection report for our client.

- Disassembly, cleaning and inspection of gearbox.
- Preparing inspection report.

- Gearbox show a heightened level of vibration TPV the teeth.
- Inspection in 2 days
- Performing: - Gearbox after entry immediately disassembled and inspected
- Any damage capturing by pictures
- Drawing up a complete inspection-report
- Stop Point.

- Disassembling, cleaning and visual inspection on gearbox SANTASALO-2C355-EY2.
- Reporting and making a revision proposal.
- Assembling revision according to revision proposal.
- Performing a test run with a test run report.

- Overhaul proposal and supplies:
- Carrying out the repair as described in our inspection report.
- The replacement of the bearings, seals and overhaul of the mechanical seal (to be determined), supply GBS Gearbox Services International.
- The renewal of various packing material like small fasteners, etc., supply GBS Gearbox Services International.
- Modification of the input shaft E-motor / gearbox according to the attached proposal with our drawing number SB93305-100.
- Renewing the E-motor, pre-consult with the customer specifications.
- The refitting the gearbox.
- If necessary, the surfaces of the lower lids due axial bearing clearances.
- Checking the supporting images and side clearances.
- Full

- Disassembly, cleaning and inspection of gearbox.
- Going through the inspection report.
- Overhaul of gearbox.

- Disassembling, cleaning and inspection on gearbox SANTASALO-3TKC280-N.
- Reporting and making a revision proposal.
- Assembling and revision according to revision proposal.
- Performing a test run with a test run report.

- Reporting and making a revision proposal.
- Assembling and revision according to revision proposal.
- Performing a test run with a test run report.

Full inspection of damaged gearbox. Afterwards we repaired this gearbox and made a test run.

Performing an inspection and overhaul of gearbox.

Performing disassembling and inspection on gearbox and creating an inspection report. Assembling of the gearbox and renew all of the parts according to the inspection report. Performing a test run and making a test run report.

Replacement and aligning of gearbox.